What Did You Do To Your HHR Today?
04-14-2017, 11:51 AM
Administrator
Join Date: 10-13-2011
Location: Welland,Ont Canada
Posts: 36,493
Friday! We're almost all packed and ready, I will do an oil change and check the brakes and torque the hub bolts and wheel lug nuts on Tuesday, Sweetie is getting her Moms stuff packed up.
I've got some things for 843de , we'll meet up with him on Friday afternoon.
The new catalytic converter has been properly broken in, the front hubs are done, rear brakes need to be cleaned and adjusted.
The cat has it figured out!
I've got some things for 843de , we'll meet up with him on Friday afternoon.
The new catalytic converter has been properly broken in, the front hubs are done, rear brakes need to be cleaned and adjusted.
The cat has it figured out!
04-14-2017, 01:53 PM
Senior Member
Join Date: 10-04-2013
Location: Gateway to the West
Posts: 902
Enjoy Florida Oldblue 
my did for today was drove my panel to
orientation for my new temp to hire job
as a sit down forklift operator.
My official first day is monday for a week of training.
After almost 5 months looking for a new job am anxious but
ready to start working again . . . . . . . . . . . . !
my did for today was drove my panel to
orientation for my new temp to hire job
as a sit down forklift operator.
My official first day is monday for a week of training.
After almost 5 months looking for a new job am anxious but
ready to start working again . . . . . . . . . . . . !
04-14-2017, 05:31 PM
New Member
Join Date: 04-11-2017
Location: California
Posts: 16
Today at lunch, I made a mock air inlet scoop. Here it is fitted up. I have a K and N coming and I want to be ready for a house reroute upon install. I plan to make one for the passenger side also for up front, just a tighter fit with a smaller scoop. I kind of wish I worked with composites as well as metal sometimes, but what metal would you guys recommended fabricating this out of?
04-15-2017, 08:55 AM
Senior Member
Join Date: 03-25-2017
Location: Ventura, CA
Posts: 235
LED Projectors
This project is canceled after I cut off the back of the reflector and bored out the hole to fit the LED bulb. After making room for the bulb, and testing the projector with the light, I can't get the assembly to focus. This, due to the fact that the LEDs only point to the sides 180 degrees apart, no forward facing light, and a big bulb housing with a large end cap squeezed into a realatively small reflector. This is not unexpected, just a little disappointing.
I have adjusted the LED bulbs in their assembly and adjusted the assembly in the halogen reflector housing and am getting better light dispersion, so for now, the LED bulbs stay.
I have adjusted the LED bulbs in their assembly and adjusted the assembly in the halogen reflector housing and am getting better light dispersion, so for now, the LED bulbs stay.
04-16-2017, 02:52 AM
Senior Member
Join Date: 03-25-2017
Location: Ventura, CA
Posts: 235
Fog Lights
CorvetteMongo,
The graphics look good!
I ordered a set of Depo fog lights today and a OEM switch for a factory add on. I'll be following the how to thread. Hopefully they work, just without the dash light. But if I have to get the computer updated, I guess I'll be handing over Chevy of Guam a small fortune.
The graphics look good!
I ordered a set of Depo fog lights today and a OEM switch for a factory add on. I'll be following the how to thread. Hopefully they work, just without the dash light. But if I have to get the computer updated, I guess I'll be handing over Chevy of Guam a small fortune.