Time to lower my drivers and pasengers seat
Just wondering if any one has lowerd their drivers seat im 6.2 and its killing my back having to lay the seat back.
|
Originally Posted by cornwalis
(Post 704898)
Just wondering if any one has lowerd their drivers seat im 6.2 and its killing my back having to lay the seat back.
|
I'm 6' 5" no issues so far I did remove the seat to clean the carpets when I bought the HHR and thought about lowering the seats but thought the cutting and welding would have only given 2 inches or so
|
I've lowered my drivers seat about 1 1/2". Look in my gallery. There are some photos of my do-it-yourself project.
|
Only other thing I wanted to do was intall power seats but not sure if the 06 hhr has the. Harness under the seat to do so or if I would have to run power to under the seat was told the power seats have a lil more ajustment than the standerd seats
|
Power seats will actually sit higher then the non powered seats.....I sit quite a bit lower in my LS compared to the SS
|
Originally Posted by cornwalis
(Post 704898)
Just wondering if any one has lowerd their drivers seat im 6.2 and its killing my back having to lay the seat back.
I'm 6ft. and have no head room problems at all. Do you have a Moon Roof? They do reduce head clearance a bit. Do you have a power seat? Is it the lowest position? I actually have my power seat in the high position and still have no clearance problem. SF |
No I dont have power seat yes I have a moon roof but with my back issues I need to sit strit up and if I do my head in in the sunroof. And up against head liner. And i cant see out my mirrors on infront of me lol Im 6.2 but I got short legs and tall upper body. I would like to put a power seat it but not sure if their is a power outlet under the seat for it. Was told by a buddy of mine the power seats go closer to the floor.
|
Well..I'm the opposite of tall...but My Ss with power, seat all the way down..isnt low enough..and cant get the base tilt I want. Now, my LS with the manual pump seat..sets on the floor, to the point where I almost have to look over the steer wheel. Theres a real noticeable difference between the two..since I;m the only driver I have considered a few time to change seat bases since the seat position never changes, except when its cleaning time. Though I will probably go with a modified rear seat mount as it would be smart to keep the power option. As far as a harness goes..its easy enough to set up a power source..
|
Originally Posted by IgottaWoody
(Post 705069)
Well..I'm the opposite of tall...but My Ss with power, seat all the way down..isnt low enough..and cant get the base tilt I want. Now, my LS with the manual pump seat..sets on the floor, to the point where I almost have to look over the steer wheel. Theres a real noticeable difference between the two..since I;m the only driver I have considered a few time to change seat bases since the seat position never changes, except when its cleaning time. Though I will probably go with a modified rear seat mount as it would be smart to keep the power option. As far as a harness goes..its easy enough to set up a power source..
The higher you raise the seat the more tilt forward you need. Mine is just enough forward tilt to do the job but no extra tilt left. SF |
I like about a 10 degree back tilt...like to feel like I'm sorta in a bucket, that way when the driving gets interesting ..my butt is planted and all my arm movement goes into the steering wheel. Hold back from my dirt tracking days I guess.... seat
is too flat |
cornwalis- Just look under the seat, if it's wired. You will see the wiring & end clip laying there.
After seeing Fireman's pic on seat lowering, I did my power seat too. The fronts just hook in, so any lowering is in the back. Which I am (as Woody stated) "in the bucket", & loving it.. With the Brody knob, I can really lean back & am almost behind the side windows. :D |
Nice tthanx going to go look for a set powe seats ya I am going to lower the back bar I wanter to cut the frobt tabs ans lower the front too but well see obxe I pull it out and start cutting ans welding
|
If you lower the back bar, the front tabs have to be trimmed to allow it to lean back to the new lower back height.
You can't cut the front tabs down to achieve any lower in front. The tabs are already down as low as possible because they mount to the unibody floor. You will have to cut and weld a new lower plate in for the front hooks. (this I don't advize unless you are a very experienced fabricator) |
Keep us all informed on how this pans out. I just bought an 06 LT with sunroof, head clearance isn't an issue for me (although I can feel my hair bushing the headliner), it's when I roll up to a stop light, and have to hunch over to see it. Thought about cutting up the braces this weekend. but with the vent ducting under the front ones, I decided against it
|
Lol now now you got my brain working wonder if cobalt seats are more comfortable than the HHR ones and have more just left or maybe a set of Malibu seats or Saturn Aura seats with power just went might be even better have to do some fabrication but they just might fit
|
That sucks. Found a power hhr drivers seat and theirs no plug in for it just a seatbelt plug
|
That sucks. Found a power hhr drivers seat and theirs no plug in for it just a seatbelt plug
|
All times are GMT -5. The time now is 01:29 PM. |
© 2024 MH Sub I, LLC dba Internet Brands