Racing Discussion Race Track Victories - DRIVE RESPONSIBLY

Drag Racing HHR SS with Manual Transmission

Thread Tools
 
Search this Thread
 
Old Jun 11, 2012 | 09:08 PM
  #1  
SafetyGuy's Avatar
Thread Starter
 
Joined: 04-02-2012
Posts: 7
From: Pawnee, IL
Drag Racing HHR SS with Manual Transmission

Hoping to get input and share experiences in launching the manual transmission. First time at the drag strip I ran a 15.444 best 1/4 mile ETA. The biggest issue I see is the launch, as I was still able to run over 96 mph. According to what I read, everyone talkes about just dumping the clutch when in launch control. Obviously this does not work as the car seems to bog down. After practicing in the last week I'm starting to see that the timining needs to be perfect on letting the clutch out quickly but not dumping what are you other guys thoughts?
Old Jun 11, 2012 | 09:25 PM
  #2  
RobSSTurbo's Avatar
Senior Member
 
Joined: 02-05-2011
Posts: 1,056
From: south florida
If was you I would take off like you would be leaving from a light. Ride the clutch out the hole to keep some of the wheel spin down. You shouldn't dump the clutch.
Old Jun 11, 2012 | 09:26 PM
  #3  
RobSSTurbo's Avatar
Senior Member
 
Joined: 02-05-2011
Posts: 1,056
From: south florida
What are your 60s?
Old Jun 11, 2012 | 09:27 PM
  #4  
ATLsilverSS's Avatar
Senior Member
 
Joined: 04-03-2009
Posts: 707
From: atlanta, ga
Originally Posted by RobSSTurbo
If was you I would take off like you would be leaving from a light. Ride the clutch out the hole to keep some of the wheel spin down. You shouldn't dump the clutch.
^^^this...feather it out....don't dump it
Old Jun 12, 2012 | 06:34 AM
  #5  
SafetyGuy's Avatar
Thread Starter
 
Joined: 04-02-2012
Posts: 7
From: Pawnee, IL
Best 60' was 2.676. I know this is where I am messing up. We should be somewhere around a 14.8 for 1/4 in stock trim. Any of you had your manual at the drag strip and if so what times you run.
Old Jun 12, 2012 | 06:49 AM
  #6  
RobSSTurbo's Avatar
Senior Member
 
Joined: 02-05-2011
Posts: 1,056
From: south florida
I'll tell ya this weekend.lol
Old Jun 12, 2012 | 08:00 AM
  #7  
foolmoon_design's Avatar
Senior Member
 
Joined: 05-13-2008
Posts: 2,075
From: Knoxville, TN
Leave soft Rob, or bring some extra driveshafts with ya, and an 18MM socket, you should be ok, with all your mods. But beware these cars hate wheel hop.
Old Jun 12, 2012 | 09:08 AM
  #8  
RobSSTurbo's Avatar
Senior Member
 
Joined: 02-05-2011
Posts: 1,056
From: south florida
I shouldn't have wheel hop with the solid tranny mounts and engine mount. I am not going let the SS dead hook on the launch. I'll burn out the clutch before I snap an axle.
Old Jun 12, 2012 | 04:10 PM
  #9  
ChevyGuySS's Avatar
Senior Member
 
Joined: 03-18-2011
Posts: 560
From: Florida
i learned that last time i went to the track, i was running like a 15.5 with just dumping the clutch and then i got down to a 13.9 with riding or feathering the clutch out of the box
Old Jun 12, 2012 | 07:13 PM
  #10  
RobSSTurbo's Avatar
Senior Member
 
Joined: 02-05-2011
Posts: 1,056
From: south florida
You should be running a 13.3 now.



All times are GMT -5. The time now is 04:51 PM.