Chevy HHR Network
0 2019/10/29 14:19:28
5 inch front , 2 inch spindles, 3 inch springs 8 inch rear , 2 inch spring perch , 2 inch spring shackles, 4 inch dearched leaf springs. I didn’t want to cut the box floor, so just c notched the frame .
5 inch front , 2 inch spindles, 3 inch springs 8 inch rear , 2 inch spring perch , 2 inch spring shackles, 4 inch dearched leaf springs. I didn’t want to cut the box floor, so just c notched the frame .
0 2019/10/28 19:22:03
0 2019/10/28 16:04:04
0 2019/10/28 16:03:58
Best picture, I could find, squeeze them sides not the round and flat , the green part will open up and unlock the bundy.
Best picture, I could find, squeeze them sides not the round and flat , the green part will open up and unlock the bundy.
0 2019/10/28 15:59:36
Poppers are required to get the door open.
Poppers are required to get the door open.
0 2019/10/28 15:34:58
0 2019/10/28 15:33:08
The 1 1/2 inch lowering spring, because the springs are pigtailed at both ends you can’t cut them. Because they are progressive rate , you can’t heat them.
The 1 1/2 inch lowering spring, because the springs are pigtailed at both ends you can’t cut them. Because they are progressive rate , you can’t heat them.
0 2019/10/28 14:19:11
The full 2 inch lowering spring
The full 2 inch lowering spring
0 2019/10/28 14:19:05
0 2019/10/28 14:17:24
0 2019/10/28 14:13:38
0 2019/10/28 14:13:31
0 2019/10/28 14:13:24
Canuck Motorsports lowering springs, a full 2 inches out back and 1 1/2 inches up front. Installed in spring of 2010 at 58,000 miles, still in the car now I sold it in October 2019 at 286,000 miles, it’s always rode nice and level. Tell ‘em Oldblue sent you!
Canuck Motorsports lowering springs, a full 2 inches out back and 1 1/2 inches up front. Installed in spring of 2010 at 58,000 miles, still in the car now I sold it in October 2019 at 286,000 miles, it’s always rode nice and level. Tell ‘em Oldblue sent you!
0 2019/10/28 14:04:29
The calipers also sprayed with the VHT paint, the larger SS rotors and caliper brackets will be in the next week or so.
The calipers also sprayed with the VHT paint, the larger SS rotors and caliper brackets will be in the next week or so.
0 2019/10/28 12:21:14
Drums now painted with VHT caliper paint , gloss black
Drums now painted with VHT caliper paint , gloss black
0 2019/10/28 12:21:08
At Sandy Neck beach
At Sandy Neck beach
0 2019/10/28 12:21:01
The BlackSwan sitting over looking the salt pond . Waiting to roll down the road , as we head home.
The BlackSwan sitting over looking the salt pond . Waiting to roll down the road , as we head home.
0 2019/10/27 11:02:33
Just in case , I decide to get another project vehicle, Sweetie says I’ll require one of these kits!
Just in case , I decide to get another project vehicle, Sweetie says I’ll require one of these kits!
0 2019/10/27 11:02:24
0 2019/10/27 06:34:58
0 2019/10/24 07:08:50
0 2019/10/24 07:07:44
The BlackSwan outside our suite at The Cove in Orleans MA.
The BlackSwan outside our suite at The Cove in Orleans MA.
0 2019/10/24 06:56:05
Wild turkeys roaming thru a lawn near Craigville Beach yesterday afternoon
Wild turkeys roaming thru a lawn near Craigville Beach yesterday afternoon
0 2019/10/24 06:55:35
This type push pin fastener , paint to match and push it in the bumper cover
This type push pin fastener , paint to match and push it in the bumper cover
0 2019/10/23 18:28:18
It’s kinda my trademark now! Definitely not an original idea.
It’s kinda my trademark now! Definitely not an original idea.
0 2019/10/23 05:41:54
I didn’t cut it , just sanded and painted the OEM chrome grille
I didn’t cut it , just sanded and painted the OEM chrome grille
0 2019/10/23 05:41:39
0 2019/10/21 17:58:02
0 2019/10/20 17:02:36
0 2019/10/20 12:22:13
The black is visible, barely, on the lower corner of the back window, more stealthy!
The black is visible, barely, on the lower corner of the back window, more stealthy!
0 2019/10/19 11:52:57
I like the higher spot top of the rear window!
I like the higher spot top of the rear window!
0 2019/10/19 11:52:47
The connection union is fully engaged and seated and not under any stress from the tube bending an inch or two from the EVAP valve. The P0455 code is no longer popping up since I did this , last Friday.
The connection union is fully engaged and seated and not under any stress from the tube bending an inch or two from the EVAP valve. The P0455 code is no longer popping up since I did this , last Friday.
0 2019/10/19 11:44:22
This is the new to me tube and fitting from a sadly wrecked HHR.
This is the new to me tube and fitting from a sadly wrecked HHR.
0 2019/10/19 11:44:14
This vapour line connection looked ugly and leaked air, so I went to local pick a part and cut the line way down by the steel line , lotsa tubing to have to measure better
This vapour line connection looked ugly and leaked air, so I went to local pick a part and cut the line way down by the steel line , lotsa tubing to have to measure better
0 2019/10/19 11:44:05
0 2019/10/18 12:17:34
0 2019/10/18 11:09:37
0 2019/10/18 08:17:16
0 2019/10/17 13:19:45
0 2019/10/17 13:17:42