Chevy HHR Network
The Red Ryder B-B gun was a fantasy gift for Ralphie in the movie A Christmas Story, which was filmed in St Catharines, Ontario.
The Red Ryder B-B gun was a fantasy gift for Ralphie in the movie A Christmas Story, which was filmed in St Catharines, Ontario.
0 2021/10/03 07:02:58
Hopefully you can see this screen shot
Hopefully you can see this screen shot
0 2021/10/03 06:16:59
0 2021/09/30 13:56:55
0 2021/09/29 12:13:33
2010 and 2011 should be this process
2010 and 2011 should be this process
0 2021/09/29 12:13:30
0 2021/09/28 16:40:47
This is a different circuit in the 2008 SS harness
This is a different circuit in the 2008 SS harness
0 2021/09/28 16:34:05
Different circuits in the cross over, not only for wires, but from different terminals as shown here in the 2009/2010 SS harness
Different circuits in the cross over, not only for wires, but from different terminals as shown here in the 2009/2010 SS harness
0 2021/09/28 16:34:03
0 2021/09/28 08:51:14
0 2021/09/27 07:44:00
The other 3 all are fairly good , just need a polish!
The other 3 all are fairly good , just need a polish!
0 2021/09/27 05:32:02
I got the 2LT rims cleaned up and mounted
I got the 2LT rims cleaned up and mounted
0 2021/09/27 05:31:57
This one has a brand new tire on it but a little curb rash to repair
This one has a brand new tire on it but a little curb rash to repair
0 2021/09/27 05:31:51
0 2021/09/27 05:00:22
0 2021/09/27 04:49:42
0 2021/09/26 13:41:24
0 2021/09/22 09:17:55
Thank you !
Thank you !
0 2021/09/22 06:44:47
I have these installed, they fit one way on the spindle , my ‘07 , these also came from the factory on my 2011.
I have these installed, they fit one way on the spindle , my ‘07 , these also came from the factory on my 2011.
0 2021/09/22 06:33:18
0 2021/09/21 12:14:08
This is the old 9.8 link
This is the old 9.8 link
0 2021/09/20 07:14:43
Up high from the rear
Up high from the rear
0 2021/09/20 07:14:37
For the top, it’s clear there’s lotsa room
For the top, it’s clear there’s lotsa room
0 2021/09/20 07:14:32
This mark on the aluminium lower control arm is from the vise , when I drilled out the ball joint rivets and pressed out the old rivets , or when I pressed out the rear bushing.
This mark on the aluminium lower control arm is from the vise , when I drilled out the ball joint rivets and pressed out the old rivets , or when I pressed out the rear bushing.
0 2021/09/20 07:10:43
0 2021/09/20 05:09:59
They fit and are not clunking at all. Yes the Moog K750012 links do have a grease zerk at each end
They fit and are not clunking at all. Yes the Moog K750012 links do have a grease zerk at each end
0 2021/09/20 05:03:56
I’ve installed Delphi TC5530 end links
I’ve installed Delphi TC5530 end links
0 2021/09/20 05:03:48
Part 2 in this photo
Part 2 in this photo
0 2021/09/19 13:27:12
Not flat like this , just bend it
Not flat like this , just bend it
0 2021/09/17 13:06:23
See how it is bent back towards the knuckle
See how it is bent back towards the knuckle
0 2021/09/17 13:05:12
An SS FE5swaybar
An SS FE5swaybar
0 2021/09/17 08:29:34
My FE3 bar
My FE3 bar
0 2021/09/17 08:29:31
Lotsa room
Lotsa room
0 2021/09/16 14:44:57
1/4 inch clearance at the bar
1/4 inch clearance at the bar
0 2021/09/16 14:44:33
Bottom of link is above the LCA and parallel to it
Bottom of link is above the LCA and parallel to it
0 2021/09/16 14:44:15
0 2021/09/15 17:05:05
0 2021/09/14 09:40:17
And here between the swaybar and LCA , the black area lower left of the photo
And here between the swaybar and LCA , the black area lower left of the photo
0 2021/09/14 09:29:03
Clearance at the swaybar at the rear
Clearance at the swaybar at the rear
0 2021/09/14 09:28:59
Same here compressed suspension, note the swaybar end is above the LCA
Same here compressed suspension, note the swaybar end is above the LCA
0 2021/09/14 09:28:54