Chevy HHR Network

General HHR Discuss anything related to the Chevy HHR that doesnt seem to fit into the more specific categories below.

Flex pipe ?

Thread Tools
 
Search this Thread
 
Old Sep 12, 2024 | 08:48 AM
Share
  #1  
Gearhead1's Avatar
Gearhead1
Thread Starter
Senior Member
 
Joined: 04-27-2021
Posts: 570
From: Alabama
Flex pipe ?
Whats a good source for just the flex pipe? 2011, LT, 2.2
Reply
Old Sep 12, 2024 | 08:50 AM
Share
  #2  
donbrew's Avatar
donbrew
Moderator
 
Joined: 01-23-2009
Posts: 26,533
From: Fredericksburg,VA
Ebay. Amazon.
Reply
Old Sep 12, 2024 | 11:45 AM
Share
  #3  
Oldblue's Avatar
Oldblue
Administrator
 
Joined: 10-13-2011
Posts: 40,083
From: Welland,Ont Canada
ZZP has a very good product as does Muffler Express , clamp or weld it!

https://mufflerexpress.ca/products/c...pair-2006-2010
Reply
Old Sep 12, 2024 | 02:53 PM
Share
  #4  
Gearhead1's Avatar
Gearhead1
Thread Starter
Senior Member
 
Joined: 04-27-2021
Posts: 570
From: Alabama
Well….friend of mine who owns a muffler/exhaust shop suggested since car had so many miles on it, to just buy section from manifold back to resonator I guess…to the 2 bolt flange anyway. So, dont no how good it will be but I bought a stainless one with the cat all welded and ready to bolt on for about 100.00 US.
Reply
Old Sep 12, 2024 | 03:03 PM
Share
  #5  
Oldblue's Avatar
Oldblue
Administrator
 
Joined: 10-13-2011
Posts: 40,083
From: Welland,Ont Canada
This one?


https://www.autoshack.ca/EM64809

Or this

https://mufflerexpress.ca/products/c...rter-2005-2007
Reply
Old Sep 12, 2024 | 03:10 PM
Share
  #6  
Gearhead1's Avatar
Gearhead1
Thread Starter
Senior Member
 
Joined: 04-27-2021
Posts: 570
From: Alabama
This one…
Reply
Old Sep 12, 2024 | 04:15 PM
Share
  #7  
PulpFriction's Avatar
PulpFriction
Senior Member
 
Joined: 12-05-2014
Posts: 3,368
From: Northern Ohio
Don't give up the OEM cat if you don't have to. The replacement will either cost a lot or die young.
Reply
Old Sep 12, 2024 | 06:43 PM
Share
  #8  
Gearhead1's Avatar
Gearhead1
Thread Starter
Senior Member
 
Joined: 04-27-2021
Posts: 570
From: Alabama
Yeah….I figured I would keep the original CAT
Reply
Old Sep 12, 2024 | 06:46 PM
Share
  #9  
Gearhead1's Avatar
Gearhead1
Thread Starter
Senior Member
 
Joined: 04-27-2021
Posts: 570
From: Alabama
Is 10.5 ft.lbs. enough torque on those exhaust manifold studs?
Reply
Old Sep 12, 2024 | 07:59 PM
Share
  #10  
RJ_RS_SS_350's Avatar
RJ_RS_SS_350
Moderator
 
Joined: 05-01-2014
Posts: 8,512
From: California
Both times I went after the exhaust manifold, there were loose bolts. I think the spec is a bit low.
Reply



Advanced Search

All times are GMT -5. The time now is 09:24 AM.