Chevy HHR Network
See it over there on the right end of the pipe!
See it over there on the right end of the pipe!
0 2022/11/24 06:05:55
This piece I cut from a Cobalt at a parts yard, longer to move that connector back by the fire wall
This piece I cut from a Cobalt at a parts yard, longer to move that connector back by the fire wall
0 2022/11/22 08:25:23
Thi was to far to the solenoid, but you can see the white retainer clip
Thi was to far to the solenoid, but you can see the white retainer clip
0 2022/11/22 08:25:22
I used this type connector for my vapour line
I used this type connector for my vapour line
0 2022/11/22 08:25:19
The right side knuckle is discontinued!
The right side knuckle is discontinued!
0 2022/11/22 05:41:05
Superceeded to another number!
Superceeded to another number!
0 2022/11/22 05:41:02
So, they have pulled the plug on forum’s like ours.
So, they have pulled the plug on forum’s like ours.
0 2022/11/21 14:33:56
0 2022/11/20 05:27:13
0 2022/11/20 05:27:07
And the page regarding the DIC programming from the 2007 owners manual
And the page regarding the DIC programming from the 2007 owners manual
0 2022/11/19 11:38:38
0 2022/11/17 09:56:02
0 2022/11/17 09:55:59
0 2022/11/17 06:29:58
That thingy with the single mounting bolt. Get a real GM AC Delco replacement if you can blow air through yours. I’ve experienced early failures of after market cheap off shore , junk
That thingy with the single mounting bolt. Get a real GM AC Delco replacement if you can blow air through yours. I’ve experienced early failures of after market cheap off shore , junk
0 2022/11/14 13:05:56
And the chrome grille with the hot rod red bars ! I missed the original look I was going for !
And the chrome grille with the hot rod red bars ! I missed the original look I was going for !
0 2022/11/12 10:18:04
Brand new coated rotors to prevent rust , I torqued the caliper bracket bolts to 85 ft/lb and the caliper bolts to the sliders at 24 ft/lb . I made sure to pump the brake pedal several times to seat the pads to the rotors as I had retracted the caliper piston in so the new pads fit into the caliper.
Brand new coated rotors to prevent rust , I torqued the caliper bracket bolts to 85 ft/lb and the caliper bolts to the sliders at 24 ft/lb . I made sure to pump the brake pedal several times to seat the pads to the rotors as I had retracted the caliper piston in so the new pads fit into the caliper.
0 2022/11/12 10:17:57
See the rust scales , and the pads have another 45,000 miles , so they will get replaced also
See the rust scales , and the pads have another 45,000 miles , so they will get replaced also
0 2022/11/12 10:17:50
These Rotors have approximately 80,000 miles on them, getting crusty in the vanes
These Rotors have approximately 80,000 miles on them, getting crusty in the vanes
0 2022/11/12 10:17:44
Part number
Part number
0 2022/11/10 17:48:10
And one of these
And one of these
0 2022/11/10 17:44:47
0 2022/11/10 17:43:00
One of these
One of these
0 2022/11/10 17:42:56
You’ll need two of these
You’ll need two of these
0 2022/11/10 17:42:53
25930724 arms are in stock, for now!
25930724 arms are in stock, for now!
0 2022/11/09 04:40:43
The 25930725 arms are currently unavailable at RockAuto, disregard these part numbers, they do not fit your HHR
The 25930725 arms are currently unavailable at RockAuto, disregard these part numbers, they do not fit your HHR
0 2022/11/09 04:40:39
A screen to monitor different functions, not a tune device
A screen to monitor different functions, not a tune device
0 2022/11/08 05:06:07
0 2022/11/07 14:54:32
The car! I can’t post many photos
The car! I can’t post many photos
0 2022/11/01 06:57:00
0 2022/11/01 06:04:20
Enjoy a safe evening!
Enjoy a safe evening!
0 2022/10/31 14:36:53
0 2022/10/31 05:24:25
Another view, this was with my old K&N FIPK kit , for the stock air filter box use the other link as a guide to mounting the can
Another view, this was with my old K&N FIPK kit , for the stock air filter box use the other link as a guide to mounting the can
0 2022/10/28 06:22:51
This is my set up in Oldblue, I used the 10 mm / 3/8 inch hose that came with the can kit.
This is my set up in Oldblue, I used the 10 mm / 3/8 inch hose that came with the can kit.
0 2022/10/28 06:22:49
0 2022/10/26 09:00:59
These are the catalytic converters under your SS . I’m thinking someone’s going to cut them they aren’t taking them to a reputable place to sell them, so marking them would be a waste of your time.
These are the catalytic converters under your SS . I’m thinking someone’s going to cut them they aren’t taking them to a reputable place to sell them, so marking them would be a waste of your time.
0 2022/10/26 05:42:59
As we read here turn the crankshaft keyway to 3 o’clock to be able to turn the camshafts and not hit the valves
As we read here turn the crankshaft keyway to 3 o’clock to be able to turn the camshafts and not hit the valves
0 2022/10/25 15:34:23
Circled in red
Circled in red
0 2022/10/25 15:32:33
Like I said key way at 12:00 And the cam phasers marks as you see intake at 2:00 o’clock and exhaust at 10:00
Like I said key way at 12:00 And the cam phasers marks as you see intake at 2:00 o’clock and exhaust at 10:00
0 2022/10/25 13:49:59
Intake at 5 o’clock and exhaust at 7 o’clock
Intake at 5 o’clock and exhaust at 7 o’clock
0 2022/10/25 13:49:57
0 2022/10/21 14:56:10