Chevy HHR Network
Driver side agosn cradle has been removed
Driver side agosn cradle has been removed
0 2024/09/12 10:21:02
Where tge cage nut is caged on the driver’s side, steering rack and swaybar removed
Where tge cage nut is caged on the driver’s side, steering rack and swaybar removed
0 2024/09/12 10:21:04
Take you angle grinder and grind these rivets on the ball joint side flat. Then centre punch them and drill 1/8 hole straight down they them , then 1/4 then 5/16. Drill the heads off with a 1/2 drill bit just until the head pops off Knock the ball joint off the lac and then drive the remaining part of the rivet out of the LCA.
Take you angle grinder and grind these rivets on the ball joint side flat. Then centre punch them and drill 1/8 hole straight down they them , then 1/4 then 5/16. Drill the heads off with a 1/2 drill bit just until the head pops off Knock the ball joint off the lac and then drive the remaining part of the rivet out of the LCA.
0 2024/09/12 10:31:26
0 2024/09/26 13:36:56
Cool looking panel!
Cool looking panel!
0 2024/10/07 13:38:05
That’s the flex vinyl pipe that goes to the fuel pump
That’s the flex vinyl pipe that goes to the fuel pump
0 2024/09/27 15:57:36
But may be it’s tge white doors
But may be it’s tge white doors
0 2024/09/26 07:40:46
0 2024/09/26 13:36:57
This valve
This valve
0 2024/09/27 11:26:21
These 4 bolts , they are 7 mm . Tighten them real tight.
These 4 bolts , they are 7 mm . Tighten them real tight.
0 2024/10/19 05:31:22
That black rubber pipe
That black rubber pipe
0 2024/10/19 12:27:18
0 2024/10/14 05:22:01
You can see the cut marks here in the old pipe bung
You can see the cut marks here in the old pipe bung
0 2024/10/12 08:26:08
Try blowing air thru the under hood EVAP valve, it should be closed. Replace the valve if air does pass thru it.
Try blowing air thru the under hood EVAP valve, it should be closed. Replace the valve if air does pass thru it.
0 2024/10/14 05:22:49
This sag gave me codes
This sag gave me codes
0 2024/10/15 09:43:07
0 2024/11/02 15:03:13
0 2024/11/02 15:03:16
0 2024/11/02 15:03:20
0 2024/11/02 15:03:28
Those four bolts ^^^^^
Those four bolts ^^^^^
0 2024/10/18 09:48:22
0 2024/10/24 04:18:33
0 2024/10/31 10:36:30
A closer look
A closer look
0 2024/10/19 12:27:22
Here is tge O2 sensor with a light coat of copper never seize ready to go into the new converter pipe.
Here is tge O2 sensor with a light coat of copper never seize ready to go into the new converter pipe.
0 2024/10/12 08:26:13
0 2024/11/02 15:03:09
0 2024/11/02 15:03:24
He invited my to his shop for more photos and details, some time in November.
He invited my to his shop for more photos and details, some time in November.
0 2024/10/19 15:28:49
Here’s the part numbers RockAuto has a good price
Here’s the part numbers RockAuto has a good price
0 2024/11/20 14:20:21
2.4 head gasket for 2008 guy
2.4 head gasket for 2008 guy
0 2024/11/22 05:05:17
2.2 gasket
2.2 gasket
0 2024/11/22 05:06:55
Brand new 2.4 block
Brand new 2.4 block
0 2024/11/22 07:00:28
0 2024/11/14 14:04:11
The rims I removed the chrome plastic covers from back in September. The colour looks good to me.
The rims I removed the chrome plastic covers from back in September. The colour looks good to me.
0 2024/11/07 12:39:17
Perhaps RJ can confirm
Perhaps RJ can confirm
0 2024/11/10 11:03:16
The part numbers are above
The part numbers are above
0 2024/11/20 14:16:55
It’s not a hard job just take your time and if you get stuck check our how to section!
It’s not a hard job just take your time and if you get stuck check our how to section!
0 2024/11/21 09:29:09
2.4 head
2.4 head
0 2024/11/22 05:25:38
These end links, seeing as you must remove the strut end most likely damaging it order two one for each side
These end links, seeing as you must remove the strut end most likely damaging it order two one for each side
0 2024/11/20 14:18:19
I got this one , same as the one from Cloyes
I got this one , same as the one from Cloyes
0 2024/11/09 05:15:26
That new 2.4 block with the head gasket in place, note there is no oil passageway for the VVT solenoids, those are in the cylinder head.
That new 2.4 block with the head gasket in place, note there is no oil passageway for the VVT solenoids, those are in the cylinder head.
0 2024/11/22 07:00:34