Chevy HHR Network
0 2019/09/22 18:08:38
0 2019/09/22 18:20:36
0 2019/09/22 18:24:55
0 2019/09/23 05:34:20
0 2019/09/23 11:41:07
0 2019/09/23 11:59:52
0 2019/09/23 13:08:38
0 2019/09/23 13:50:44
0 2019/09/23 14:08:30
0 2019/09/23 17:25:03
Chaffed wire harness
Chaffed wire harness
0 2019/09/23 19:18:42
0 2019/09/24 08:08:09
0 2019/09/25 06:01:08
0 2019/09/28 07:21:03
0 2019/09/29 05:25:00
0 2019/09/30 14:29:54
0 2019/09/30 15:17:07
0 2019/10/01 05:25:40
Here at the front under the drivers side at the front clip
Here at the front under the drivers side at the front clip
0 2019/10/01 05:28:50
A little farther back , no fuel yet be rust at the clip
A little farther back , no fuel yet be rust at the clip
0 2019/10/01 05:28:56
Here just in front of the drivers side rear tire where the insulation starts
Here just in front of the drivers side rear tire where the insulation starts
0 2019/10/01 05:29:02
And here where the lines go across to the passengers side up above the EVAP canister.
And here where the lines go across to the passengers side up above the EVAP canister.
0 2019/10/01 05:29:09
After removing the insulation I found the vapour line was perforated with rust
After removing the insulation I found the vapour line was perforated with rust
0 2019/10/01 05:39:39
The line crumbled , this was under the insulation
The line crumbled , this was under the insulation
0 2019/10/01 05:39:51
This was the fuel line just as rusted but not fully through just a pin hole , noted the drip on Saturday night.
This was the fuel line just as rusted but not fully through just a pin hole , noted the drip on Saturday night.
0 2019/10/01 05:40:02
This is the fuel soaked insulation, it held moist up in there most likely from condensation
This is the fuel soaked insulation, it held moist up in there most likely from condensation
0 2019/10/01 05:40:13
This is the EVAP canister end of the vapour line , you simply squeeze the flat area and the rounded area gently together with pliers and remove from the plastic tube it’s attached to
This is the EVAP canister end of the vapour line , you simply squeeze the flat area and the rounded area gently together with pliers and remove from the plastic tube it’s attached to
0 2019/10/01 05:45:39
I used this 3/8’s line tool to remove the fuel rail end , gently push down, then insert the tool and push into the fitting a slide it up and off the pipe
I used this 3/8’s line tool to remove the fuel rail end , gently push down, then insert the tool and push into the fitting a slide it up and off the pipe
0 2019/10/01 05:45:50
Up under the hood , I routed the new lines up to the fuel pie on the fuel rail and connected the fitting, then the vapour line , the instructions tell you to cut the old line an use the supplied coupler in the hose , that piece with the blue rings.
Up under the hood , I routed the new lines up to the fuel pie on the fuel rail and connected the fitting, then the vapour line , the instructions tell you to cut the old line an use the supplied coupler in the hose , that piece with the blue rings.
0 2019/10/01 05:58:14
Up under the back after installing all the clips to support the nylon tubes, I connected the fuel pressure line and the vapour line, and tie wrapped the now dried in the sun insulation above the exhaust pipe. I strongly suggest you wear mechanics gloves , I didn’t, but in hind sight , a couple of bucks at HF , and even if they get soaked in fuel and throw them away. It’s better the scratches and abrasions on my hands.
Up under the back after installing all the clips to support the nylon tubes, I connected the fuel pressure line and the vapour line, and tie wrapped the now dried in the sun insulation above the exhaust pipe. I strongly suggest you wear mechanics gloves , I didn’t, but in hind sight , a couple of bucks at HF , and even if they get soaked in fuel and throw them away. It’s better the scratches and abrasions on my hands.
0 2019/10/01 05:58:21
0 2019/10/01 06:25:40
I clipped all the nylon or plastic lines into the line brackets and covered them in exposed to road debris area to protect from abrasions
I clipped all the nylon or plastic lines into the line brackets and covered them in exposed to road debris area to protect from abrasions
0 2019/10/01 11:40:10
I took the time to route the new lines thru the long protective bracket
I took the time to route the new lines thru the long protective bracket
0 2019/10/01 11:40:17
Same for the area where the line go up and over the exhaust. I wrap them with the insulation and ty wrapped them
Same for the area where the line go up and over the exhaust. I wrap them with the insulation and ty wrapped them
0 2019/10/01 11:40:26
This is over the rear axle and exhaust pipe, insulation sleeve and ty wraps
This is over the rear axle and exhaust pipe, insulation sleeve and ty wraps
0 2019/10/01 11:40:34
Here’s the connection for the vapour line to the EVAP canister
Here’s the connection for the vapour line to the EVAP canister
0 2019/10/01 11:40:41
This is the pressure line connection to the pipe that goes over the fuel tank to the fuel pump.
This is the pressure line connection to the pipe that goes over the fuel tank to the fuel pump.
0 2019/10/01 11:40:48
0 2019/10/01 11:40:56
This is the kit I ordered, much less shipping then the full stainless steel kit I installed in Oldblue in April of 2018. Much easier to put into place . The lines are good quality, the ends are preinstalled except the front end of the vapour line.
This is the kit I ordered, much less shipping then the full stainless steel kit I installed in Oldblue in April of 2018. Much easier to put into place . The lines are good quality, the ends are preinstalled except the front end of the vapour line.
0 2019/10/01 11:49:22
0 2019/10/02 06:04:01